The Effects of Morphology and Surface Oxidation of Stainless Steel Powder in Laser Based-Powder Bed Fusion
Licentiate thesis, 2020

Laser based-powder bed fusion (LB-PBF) is one of the many techniques within additive manufacturing (AM) that allows for near net shape manufacturing of metallic components. By using powder feedstock, it is possible to spread thin layers of powder and further selectively fuse powder in a repetitive manner until the component is completed. The majority of the powder grades for AM are produced using vacuum induction melting and inert gas atomization (VIGA). The process produces spherical powder with high purity, but at a premium cost. In order to improve the utilization of LB-PBF further, more cost-efficient powder grades must be introduced to the market.

This work therefore addresses three grades of 316L stainless steel powder with regard to the surface oxide characteristics and processability in AM, a vacuum induction melted and inert gas atomized (VIGA) grade, an air-melted and nitrogen gas atomized (GA) grade and a water-atomized (WA) grade. The chemical surface characterization revealed that the two gas-atomized powders had comparable oxidation states, with minor differences in particulate coverage between the two grades. Since the GA powder contained more Si, it was found in higher concentrations in the oxide particulates. The WA grade, however, had a larger surface coverage of particulates (rich in Cr and Si), yet had a thinner oxide layer surrounding the particulates compared to the gas atomized grades. However, the particulate features on the WA grade did not seem to affect the printability, as densities of > 99.95% were reached without discernible defects in the microstructure. While the printability was comparable with the GA grade at a layer thickness of 20 µm, the limitation of the WA powder were noticed at a higher layer thicknesses (40 µm), where up to about 1 vol.% of porosity was obtained.

Furthermore, LB-PBF processing of WA powder was found to result in a rather homogenous precipitation of nanometric oxide inclusions within the microstructure. Consequently, this work investigated whether the oxide inclusions could contribute to an oxide dispersion strengthening effect. The average size of these oxides was found to be 56 nm, with an average number density of 2.8 × 1015 m-3. The oxides were observed to be amorphous with a characteristic core-shell structure. Concerning the mechanical strength, the WA samples had slightly reduced yield strength (~500 MPa) in comparison to the GA samples (~600 MPa). Hence, no oxide dispersion strengthening effect was observed, as the average size and number density of oxides was not optimized.

powder properties

316L stainless steel

laser based-powder bed fusion

oxides

oxidation

powder surface

additive manufacturing

morphology

powder production

VDL, Chalmers Tvärgata 4C
Opponent: Dr. Seshendra Karamchedu, Uddeholms AB, Sweden

Author

Dmitri Riabov

Chalmers, Industrial and Materials Science, Materials and manufacture

Riabov, D., Hryha E., Rashidi M., Bengtsson, S., Nyborg L., Effect of Atomization on Surface Oxide Composition in 316L Stainless Steel Powders for Additive Manufacturing

Factors Affecting Printability of 316L Powders Using the DMLS Process

Proceedings of World PM 2018,; (2018)

Paper in proceedings

Riabov D., Rashidi M., Hryha E., Bengtsson S., Effect of the powder feedstock on the oxide dispersion strengthening of 316L stainless steel produced by laser powder bed fusion

Subject Categories

Materials Engineering

Metallurgy and Metallic Materials

Areas of Advance

Materials Science

Thesis for the degree of licentiate of engineering / Department of Materials Science and Engineering, Chalmers University of Technology: IMS-2020-4

Publisher

Chalmers University of Technology

VDL, Chalmers Tvärgata 4C

Online

Opponent: Dr. Seshendra Karamchedu, Uddeholms AB, Sweden

More information

Latest update

5/6/2020 8