Towards ultraviolet and blue microcavity lasers
Paper i proceeding, 2018

The development of III-nitride-based (Al,Ga,In(N)) microcavity lasers is a challenging task. Significant progress in recent years has resulted in realizations of electrically pumped devices with optical output power in the mW-range and with threshold current densities below 20 kA/cm2. However, to become practical, the lifetime and power conversion efficiency of these devices must be improved. Among the challenges are achieving transverse optical mode confinement, highreflectivity mirrors and control over the resonator length. We will highlight our theoretical work on transverse optical mode confinement, emphasising the overwhelming risk of ending up with an optically anti-guided cavity, and its consequences such as very high optical losses that easily could double the threshold gain for lasing. We will show some anti-guided cavities with reasonable threshold gain and built-in modal discrimination. However, all anti-guided cavities are very sensitive to temperature effects and small structural changes in the cavity caused by fabrication imperfections. We have explored electrically conductive distributed Bragg reflectors (DBRs) in both AlN/GaN and ZnO/GaN. The AlN/GaN DBRs were grown with different strain-compensating interlayers, and the DBR without interlayers had the lowest vertical resistivity with a specific series resistance of 0.044 cmfor eight DBRpairs. In the ZnO/GaN DBR, the measured resistance was dominated by lateral and contact contributions, setting a lower measurable limit of ~10 for three DBR-pairs. Numerical simulations show the importance of having in-plane strained layers in the ZnO/GaN DBR, since that leads to cancellation of the spontaneous and piezoelectric polarization. This results in a dramatically reduced vertical resistance, potentially three orders of magnitude lower than what could be measured. cm An alternative to an epitaxially grown DBR is a dielectric DBR, which offers high reflectivity over a broader wavelength range, relaxing the requirements on resonator length control. To deposit a dielectric DBR on the bottom side of the cavity, the sample must first be bonded to a carrier wafer before the substrate can be removed. We used thermocompression gold-gold bonding to successfully bond the laser structure to a Si carrier wafer. The subsequent substrate removal is a challenging process due to the chemical inertness of the III-nitride-based materials. A doping-dependent electrochemical etch technique was used, which allows for the selective removal of a sacrificial (n-doped) layer between the cavity and the substrate. This resulted in nm-precise cavity lift-off with a low root-mean-square surface roughness down to 0.3 nm. Thus, the process is suitable for the fabrication of high-quality optical devices such as microcavity lasers. In addition, the technique offers a new alternative to create III-nitridebased optical resonators, mechanical resonators, thin film LEDs and transistors.

ultraviolet

electrochemical etching

microcavity laser

DBR

blue

Författare

Michael Alexander Bergmann

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Filip Hjort

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Seyed Ehsan Hashemi

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

David Adolph

Chalmers, Mikroteknologi och nanovetenskap, Mikrovågselektronik

Martin Stattin

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Tommy Ive

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Jörgen Bengtsson

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Johan Gustavsson

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Åsa Haglund

Chalmers, Mikroteknologi och nanovetenskap, Fotonik

Northen Optics and Photonics conference

Vol. 2018
978-91-639-6488-6 (ISBN)

Northen Optics and Photonics conference
Lund, Sweden,

Styrkeområden

Nanovetenskap och nanoteknik

Materialvetenskap

Ämneskategorier

Fysik

Annan materialteknik

Elektroteknik och elektronik

Nanoteknik

Infrastruktur

Chalmers materialanalyslaboratorium

Nanotekniklaboratoriet

Mer information

Senast uppdaterat

2023-10-27