Decision and Planning for Additive Manufacturing Implementation in the Early Design Phase
Doktorsavhandling, 2026
assessed and what was prioritised in the decision. It also identified where each method needs further development. The thesis extends the scope of Design for Additive Manufacturing (DfAM), from how to design for AM to also whether and when to use it.
Engineering Design
Decision Support
Design for AM
Additive Manufacturing
Författare
Tina Hajali
Chalmers, Industri- och materialvetenskap, Produktutveckling
The Importance of Digitalisation in Industrialising Additive Manufacturing: Learnings from the DIDAM P2030 Project
Advances in Transdisciplinary Engineering,;Vol. 52(2024)p. 442-452
Paper i proceeding
INFORMATION FLOW ANALYSIS ENABLING THE INTRODUCTION OF ADDITIVE MANUFACTURING FOR PRODUCTION TOOLS-INSIGHTS FROM AN INDUSTRIAL CASE
Proceedings of the Design Society,;Vol. 3(2023)p. 2315-2324
Paper i proceeding
Feasibility and suitability analysis of additive manufacturing in pre-conceptual design phase
Journal of Engineering Design,;Vol. 37(2026)p. 702-740
Artikel i vetenskaplig tidskrift
An iterative investigation of needs and barriers in deciding when to design for additive manufacturing
Proceedings of the International Conference on Engineering Design, ICED,;Vol. 6(2026)p. 1971-1980
Paper i proceeding
A risk analysis method for implementation of additive manufacturing
Journal of Engineering Design,;Vol. 37(2026)p. 311-338
Artikel i vetenskaplig tidskrift
Hajali, T., Brahma, A., & Isaksson, O. (2026). Assessing risks and opportunities for additive manufacturing implementation [Manuscript in press]. Journal of Engineering Design.
In this thesis, how this decision, whether and when to use AM, can be supported in the early design phase is investigated. The needs and barriers that shape the decision from both operational and strategic perspectives are identified through literature reviews, industrial case studies, interviews, workshops and controlled experiments. These are translated into criteria for a decision support, structured through the Feasibility, Suitability, Viability (FSV) framework, which distinguishes whether AM can be used from whether it should be. To operationalise the framework, two methods are proposed, each implemented as a working prototype and evaluated in controlled experiments with academic and industrial participants. The evaluation showed positive results for both methods in terms of usefulness and usability, and identified where each needs further development.
The contribution is to both science and practice. To science, design for additive manufacturing (DfAM) is extended from how to design for AM to whether and when to use it. To practice, two evaluated methods with working prototypes are offered, moving the decision from a late, intuitive judgement to an early, system-level assessment.
Digital Sustainability Implementation Package (DSIP)
VINNOVA, 2021-03-01 -- 2023-03-01.
VINNOVA (2020-04163), 2021-03-01 -- 2023-03-01.
Materialeffektiva försörjningskedjor genom decentraliserad additivtillverkning för exportindustrin MATER-AM
VINNOVA (2023-02499), 2023-10-19 -- 2024-05-31.
Demonstration of Infrastructure for Digitalization enabling industrialization of Additive Manufacturing (DiDAM)
VINNOVA, 2020-02-20 -- 2023-02-20.
VINNOVA (2019-05591), 2020-02-20 -- 2023-02-20.
Ämneskategorier (SSIF 2025)
Produktionsteknik, arbetsvetenskap och ergonomi
Annan teknik
Drivkrafter
Hållbar utveckling
Innovation och entreprenörskap
Styrkeområden
Produktion
Infrastruktur
Additiv tillverkning vid Chalmers
DOI
10.63959/chalmers.dt/5982
ISBN
978-91-8103-525-4
Doktorsavhandlingar vid Chalmers tekniska högskola. Ny serie: 5982
Utgivare
Chalmers