Methane emissions from industrial activities using drones
Rapport, 2023

Innovative drone-based methods have been developed to map and quantify methane leakages from various industrial activities, such as refineries, Liquified Natural Gas (LNG) terminals, landfills, and water treatment facilities. These methods use a high-speed, high-sensitivity laser sensor and were validated through controlled gas releases. They were also compared to a ground-based infrared absorption-based technique. This initiative is supported by the Swedish Governmental Agency for Innovation Systems (Vinnova) and aligns with UN Sustainable Development Goals 9, 11, and 13. The goal is to reduce methane emissions significantly, aiding Sweden in achieving net-zero greenhouse gas emissions by 2045. Accurate measurements enable effective, targeted, and trackable measures to minimize emissions, resulting in a rapid positive climate impact. The project has led to the development of two distinct drone-based methods: the wall approach and the tracer approach. The wall approach measures gas concentrations across the entire cross-section of the plume, whereas the tracer approach measures the ratio of leaking gas to source gas. Depending on the source's size, one approach may be preferred over the other, with the tracer method being more suitable for point sources and the wall approach for larger sources. The custom-designed drone in this project, provided and operated by Gerdes Solution. is equipped with a high-sensitivity laser sensor and has a flight duration of about 12 minutes while carrying a 3 kg payload. This limitation presents a challenge when conducting wall measurements, which require approximately 25 minutes of flight time for the studied sources. Due to the drone's limited flight time, it necessitates landing and battery replacement, which complicates the process and limits the number of repeat measurements. In future endeavors, employing a drone with a longer flight duration would be advantageous. In total, the study detected about 220 kg/h of methane emissions and 3 kg/h of nitrous oxide emissions, equivalent to an emission rate of about 7 tons/h of carbon dioxide. The emissions were dominated by the water treatment plant and landfills, with relatively little coming from the refinery and LNG plant. However, the wall measurements in thus study serve as demonstrations of how the technique can be used and do not provide a comprehensive picture of the actual emissions from the individual sites; this would require more statistical data in terms of repeat measurements and measurement days. It is shown that drone measurements using the new high sensitivity laser is a valuable tool for mapping methane concentrations from various types of industrial sources, which are challenging to investigate today due to diffuse emissions, large dimensions, and complex geometries.

The validation studies show that both the wall approach and controlled tracer releases can be used to quantify emissions, achieving an accuracy of up to 10 % for a simple, single, source. However, in the real measurement situation, the wall approach may be difficult to execute due to practical challenges like flying restrictions and the need for spatially dense data that can be interpolated to a homogenous grid and repeated measurements. In several cases, when the drone had to fly relatively close to the plumes, downwind of large buildings in complex and turbulent wind fields, the wall approach yielded large variability in the resulting flux. It is hence evident that the wall approach requires a thorough understanding of the measurement situation, and that repeated measurements are needed, at different distances from the source and in varying wind directions. The tracer approach was therefore preferred choice for obtaining emission rates in this study, although it is challenging to carry out representative tracer releases for larger sources and for cases when the measurements are performed near to the source, and in this case the wall approach is preferred. It was also shown that the drone-based tracer approach is advantageous to the ground based since it is then easier to capture the full plume.

Författare

Johan Mellqvist

Chalmers, Rymd-, geo- och miljövetenskap, Geovetenskap och fjärranalys

Alexander Vladimir Conde Jacobo

Chalmers, Rymd-, geo- och miljövetenskap, Geovetenskap och fjärranalys

Sumedh Bandodkar

FluxSense AB

Samuel Brohede

FluxSense AB

Pontus Andersson

FluxSense AB

Brian Offerle

FluxSense AB

Jerker Samuelsson

FluxSense AB

Mätning av metangasutsläpp från industriella aktiviteter med drönare

VINNOVA (2021-04561), 2021-11-01 -- 2022-11-25.

Drivkrafter

Hållbar utveckling

Ämneskategorier

Meteorologi och atmosfärforskning

Miljövetenskap

DOI

10.17196/see.drone-vinnova-report.2023

Utgivare

Chalmers

Mer information

Senast uppdaterat

2023-06-02